Minimalist Trading
  1. Home
  2. Learn
  3. ATR stop loss and position size

ATR stop loss and position size

A fixed 20-pip stop is tight on a quiet day and noise on a busy one. The average true range (ATR) measures how far a market normally moves, so the stop can scale with it and the position size can scale the other way.

  • 7 min read
  • By a.b
  • Updated November 2026

What the ATR is

The average true range comes from J. Welles Wilder's 1978 book New Concepts in Technical Trading Systems. For each bar the true range is the largest of three numbers: high − low, the absolute value of high − previous close, and the absolute value of low − previous close. The second and third cover gaps between bars. The ATR is an average of the true range over N bars; Wilder used N = 14 with his own smoothing, and many charting platforms offer a simple-average version, so the two can differ slightly. Check which one your platform uses.

Worked example: five invented daily bars

The bars below are made up for illustration (E), not market data. Previous close before day 1 is 1.0800.

DayHighLowPrevious closeHigh − Low (pips)|High − prev close||Low − prev close|True range (pips)
11.08601.07901.080070601070
21.08901.08101.084080503080
31.08501.07601.082090306090
41.08001.07201.077080305080
51.08801.07801.07901009010100

The five true ranges average to 84.0 pips. A real ATR(14) uses fourteen bars; five keeps the arithmetic visible.

From ATR to a stop

The stop distance is a multiple of the ATR: stop = entry ∓ k × ATR, below the entry for a long trade, above for a short. The multiple k is a choice, not a rule. A small k is hit more often by ordinary noise; a large k is hit less often but costs more per trade. Nothing here says which k is best; test it on your own chart and record the result.

From the stop to the position size

Once the stop is in pips the size follows the usual formula in how to calculate position size: lots = risk ÷ (stop in pips × pip value per lot). With a $100 risk on EUR/USD ($10 per pip per 1.00 lot, see pip value) and the ATR of 84.0 pips:

Stop distanceIn pipsExact lots (risk $100, $10 per pip per lot)Rounded downLoss if stopped
1 × ATR84.0 pips0.1190.11$92.40
1.5 × ATR126.0 pips0.0790.07$88.20
2 × ATR168.0 pips0.0600.05$84.00
3 × ATR252.0 pips0.0400.03$75.60

The pattern to notice: doubling the stop halves the lots, so the loss if stopped stays near $100 whichever multiple you pick. The ATR does not change how much you risk; it changes how many lots that risk buys.

Gold example, with the contract-size caveat

Suppose gold has an ATR of $20, a 1.5 × ATR stop is $30, and one lot is 100 troy ounces, so a $1 move on 1.00 lot is $100. Lots = 100 ÷ (30 × 100) = 0.0333, rounded down to 0.03. Sources and brokers disagree on what a "pip" is for gold and on the lot size (100 oz is common, not universal), so read the contract size in your platform's symbol specification before you use these figures. See gold lot size and pip value.

Limits of the method

  • The ATR describes the past. A volatility jump, for example around a data release, can exceed it in one bar.
  • The timeframe matters. A daily ATR on a 5-minute trade gives a stop far too wide; use the ATR of the chart you trade.
  • A stop placed only by ATR ignores structure. Many traders check the result against a nearby swing high or low, or a level such as those marked by Support & Resistance Zones, and skip the trade if the level-based stop needs a much larger distance than the risk allows.
  • Spread is extra: see what the spread costs.

Using it

  1. Read the ATR for the chart you trade from your platform and note its smoothing.
  2. Pick a multiple and write it in your plan before the trade.
  3. Put the stop in pips into the position size calculator or lot size calculator with your risk amount.
  4. Check the reward-to-risk of the trade with the risk reward calculator.

Leveraged trading can lose money. This page is education, not advice.

Pre-set for the market you trade

Pip, point and tick values differ by instrument. These calculators start from each one's contract, with worked examples:

See all instrument calculators →

Quick questions

How do I set a stop loss with ATR?

Multiply the ATR of the chart you trade by a chosen multiple (for example 1.5) and place the stop that distance from the entry, below for a long and above for a short.

What ATR period should I use?

Wilder's original setting is 14 bars, and it is the default on most platforms. The right period is a choice; keep it the same while you compare results.

Does a wider ATR stop mean more risk?

Not if you size from it. A wider stop means fewer lots for the same money risked, so the loss if stopped stays about the same.

Is ATR the same on every platform?

No. Wilder used a smoothed average; some platforms use a simple average of the true range, so the values differ slightly.

Keep reading

a.b

Written by a.b. I joined TradingView in December 2015 and publish indicators there. These guides are for education only. Message me on TradingView chat with questions or topics you want covered.

Last updated November 2026. For education only. Not financial advice.